Форум обсуждение

Send message

[ +7-981-8529467 (Санкт-Петербург)

t.me/os2_guru

 
Update

 
Applications

 
Advantages:

 
For developer:

 
(Пайпы программ)

 
Companies:

 
History:

 
(Бонусы)

 
Advice:

 
(Барьеры и решения)

 
Technologies:

 
(Применение в науке, лаборатории, ..)

 
Solutions

 
New eComStation:

 
Future:

 
(Ссылки на другие сайты)

 
(Картинка дня)

 
OS/2 artefacts:

 
Gadgets:

Hardware > Notebooks/barebones Acer Travelmate 5720 Homepage: Specification

?>

Acer Travelmate 5720

Mark: Average

(This report is prepared by ecomstation.ru scout), source of information: Peter Brown

eCS 2.0 GA

I got conned into this by my son who has just purchased this "2nd user" laptop. An interesting experience ...

• 1st attempt with install options set to Modern Hardware, Safe mode using Panorama video driver: Very slow getting past the eCS2 splash screen but, eventually, the Installer appeared. All went well until I tried to read the Reg Key from a USB drive - the USB ports do not seem to be working, the drive is not recognised and no message appears telling me the device ?: has been attached.
• 2nd attempt with install options set to Modern Hardware, ACPI mode using SNAP video driver (VBE mode automatically selected by SNAP): Very quickly past the eCS2 splash screen and the Installer appeared. No problems accessing the usb drive with the Reg Key on. Install completed OK but there were problems.

Devices:

• No system sounds - have to investigate the different uniaud packages and see if I can some drivers that work.
• Having added /SMP and /APIC to the PSD=ACPI.PSD line I rebooted.
• I could not get a wireless connection; the (genmac) drivers for the Intel 3945 nic seemed to load OK but failed to connect to the router almost next to the laptop.
• I removed the other nic driver (Broadcom, wired socket and not required) and protocols using the Adapters and Protocols app and rebooted. No change, still no wireless connection.
• The system also seems a bit "off" in that it "pauses" for a short period of time when it is possible to move the mouse pointer but it is not possible to actually click on anything. The cpu meters also stop moving during these "pauses". I suspect ACPI problems...

I decided to try changing the PSD= line in config.sys again and replaced /APIC with /PIC and rebooted. That worked fine, the laptop can now "internet" successfully and the system "pauses" are gone :-)

Looks like my suspicion of ACPI problems was correct.

Still no audio so I'll have to look into that a bit further.

Overall, quite a nice laptop - shame the install needed so much faffing around though.

Information is sent by: eComStation.RU Scout -- 2010-12-08 14:16:48

[GoogleAdv]

Comments:

Peter Brown 2010-12-08 22:54:56

Just to update the above on the lack of audio here is a post made to the uniaud mailing list on the subject: I'm trying to get audio working on an Acer Travelmate 5720 laptop with Intel HDA (ICH8?) and Realtek ALC268 mixer. I have tried various uniaud builds and am currently using uniaud195-1924-v2 All drivers tested seem to load at boot displaying something like HDA Intel at xxxxxx IRQ11 - where xxxxxx is some sort of address? None of the drivers tested play any system sounds - yes System Sounds are Enabled and a Scheme is selected. Using this command in the \mmos2 directory unimix -list > uniaud_cntrls.txt creates a list of Control IDs and shows their state. Control ID1 has the Name: [Speaker Playback Volume] which has Count of values: 2; both values show as 0 I used unimix to try to turn these on: unimix -id1 -cnt0 -val64 unimix -id1 -cnt1 -val64 Both attempts gave a success message and sound seems to play fine; the following command shows both speakers active unimix -list > unitest.txt Both vlc and (s)mplayer seem to work OK. A little later I had to reboot and "lost" sounds again. I ran unimix -list > unitest2.txt and both speakers had been reset to 0. I guess I need to set the speaker playback volume values at every boot. What is the best way to go about this? Well, the easy answer is to create a CMD file with the above unimix commands to set volume and put a shadow of the CMD file in the Startup folder. Another alternative would be to put the commands in startup.cmd in the root of the boot drive.

Comment this note (add comments, don't expect that other users will reply or join discussions here)
	Your Name: Your E-Mail: CODE:
Your Comment:

eCo Software was participating in the development of drivers: ACPI - OS kernel, resources management, power management Panorama VESA - universal video driver JFS - boot feature implemented Uniaud - initial support of HDAudio USB - restore of source code

 
For dummies

 
Reviews